![]() ![]() See our guide on the best 40mm fans for 3D printers. In this case, you can install quieter fans. Therefore, the printer cannot be made quieter without completely replacing the mainboard by installing quieter drivers. ![]() The mainboard has permanently integrated drivers on the circuit board. The lack of a cover on the underside makes the fan in the power supply noisy during printing operations. ![]() The rest of the processing of the printer is also exemplary. No cable was disconnected or looked to be in any way. The wiring is fine to my non-electrician mind. If you put the printer on a screwdriver or the like, a short circuit or the like could very quickly occur. That is why the bottom of the photo above is also green, because any LED on the circuit board is green.įor my part, the lack of cover on the underside does not seem right. This time I didn’t have to bother to unscrew the printer because there is no cover on the bottom. Therefore, roughly speaking, only the axles have to be mounted and the motors connected to the wiring harness. ![]() The electronics are located at the bottom of the housing. Assembly Processįor the most part, the assembly is quite simple and can be done in 30-60 minutes. So a couple of screws and a small sensor are also included twice in the scope of delivery. There is a little spare material for that. Tweezers and the usual blue pliers are missing. Apart from that, the necessary tools, a card reader and a small spatula are included in the scope of delivery. The screws are exemplary packed in labeled bags. After unboxing the package, you can start assembling the device either according to instructions on the manual or the video instructions. Only the electronics are already installed in the lower housing.Īpart from that, the items are packed in the usual Tetris manner. The structure is a bit more extensive, since the printer is not delivered pre-assembled to a large extent. A variety of screws packed in well-labeled bags.This immediately solved the problem, everything prints fine now, without having to update the firmware or do anything else.When you purchase the JGMaker Magic 3D printer review, this is what you’ll get in the box: I found an old 2 GB SD card from a digital camera I haven't used in years, deleted all the images from it, and put my gcode files on there. After reading this forum I was prepared to try updating the firmware, but thought I would just try a different SD card first. Being a complete novice to 3D printing I assumed I was doing something wrong with slicing and producing new gcode files, and tried various different settings as well as different versions of Cura, all to no avail. Some would start but not finish, while with others the machine said it was printing but would not actually do anything, even though the progress meter would move to 100%. I had the same problem as others, where the test piece would print just fine from the SD card which came with the printer, but no other gcode files I had sliced with Cura would print. I have notified the factory today and hope to get some recommendations from them tomorrow. I am really confused and certainly no expert on gcode, but can't understand why the exact same gcode downloaded to my new 128g SD card, freshly reformatted would not even be recognized by the printer's SD card reader. again printed and mine acted as it had before.no movement, but appeared to think it was printing. I edited the start code on my obj gcode file to be exactly the same as the test code saved them both and downloaded both back on to the 8g card. I actually put both the test gcode and my object gcode in the repetier host to look at the start code. When I loaded the gcode files I created using my own object (small sculpture) created using meshroom/meshmixer onto the original 8G SD card the printer recognized the files, however when I selected the gcode file to print it did as other have said.appeared to think it was printing since the % completed kept going up, however nothing was happening, no X,Y or Z movement at all.įor whatever reason I can still print the original test piece off the 8g card. When I put my new SD card in the printer (after confirming on my computer that the files existed on the card) the printer doesn't appear to see the files at all. I have tried a new SD card, completed reformatted it and tried loading both the test object and one I had created using both the JGcreat and Cura slicers provided. I am a newbie as well and my problem is similar except that I have been unable to print the original test obj. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |